=> setenv rootpath /opt/eldk-4.2/ppc_85xx/ => run flash_nfs ## Booting kernel from Legacy Image at fe000000 ... Image Name: Linux-2.6.26-rc5-dirty Created: 2008-06-08 12:06:49 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1439783 Bytes = 1.4 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK ## Flattened Device Tree blob at ffec0000 Booting using the fdt blob at 0xffec0000 Loading Device Tree to 007fd000, end 007ff8e0 ... OK Using TQM85xx machine description Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb Linux version 2.6.26-rc5-dirty (wolf@pollux.denx.de) (gcc version 4.2.2) #1 Sun Jun 8 14:06:27 MEST 2008 console [udbg0] enabled setup_arch: bootmem tqm85xx_setup_arch() Found FSL PCI host bridge at 0x00000000e0008000. Firmware bus number: 0->0 PCI host bridge /pci@e0008000 (primary) ranges: MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000 IO 0x00000000e2000000..0x00000000e2ffffff -> 0x0000000000000000 Found FSL PCI host bridge at 0x00000000e000a000. Firmware bus number: 0->1 PCI host bridge /pcie@e000a000 ranges: MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000 IO 0x00000000ef000000..0x00000000f6ffffff -> 0x0000000000000000 arch: exit Zone PFN ranges: DMA 0 -> 131072 Normal 131072 -> 131072 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 131072 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: root=/dev/nfs rw nfsroot=192.168.3.1:/opt/eldk-4.2/ppc_85xx/ ip=192.168.210.7:192.168.3.1::255.255.0.0:tqm8548:eth3:off panic=1 console=ttyS0,115200 mpic: Setting up MPIC " OpenPIC " version 1.2 at e0040000, max 1 CPUs mpic: ISU size: 80, shift: 7, mask: 7f mpic: Initializing for 80 sources PID hash table entries: 2048 (order: 11, 8192 bytes) clocksource: timebase mult[3c00001] shift[22] registered Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 516352k/524288k available (2812k kernel code, 7620k reserved, 108k data, 104k bss, 144k init) SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Mount-cache hash table entries: 512 net_namespace: 192 bytes NET: Registered protocol family 16 PCI: Probing PCI hardware PCI: 0001:01:00.0: class b20 doesn't match header type 01. Ignoring class. PCI: Cannot allocate resource region 2 of device 0000:00:1c.0, will remap PCI: Cannot allocate resource region 2 of device 0001:02:00.0, will remap PCI: Cannot allocate resource region 2 of device 0001:02:00.1, will remap PCI: Bridge: 0001:01:00.0 IO window: 0000-0fff MEM window: 0xc0000000-0xc00fffff PREFETCH window: 0x00000000c0100000-0x00000000c01fffff pci 0001:01:00.0: enabling device (0106 -> 0107) NET: Registered protocol family 2 IP route cache hash table entries: 16384 (order: 4, 65536 bytes) TCP established hash table entries: 65536 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 65536 bind 65536) TCP reno registered NET: Registered protocol family 1 msgmni has been set to 1009 for ipc namespace c02ce3dc io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered aer: probe of 0001:01:00.0:pcie01 failed with error -38 Generic RTC Driver v1.07 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 42) is a 16550A console handover: boot [udbg0] -> real [ttyS0] serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 42) is a 16550A brd: module loaded loop: module loaded Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI Copyright (c) 1999-2006 Intel Corporation. e1000: 0000:00:1c.0: e1000_probe: (PCI:66MHz:32-bit) 00:0e:0c:d7:f5:f4 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection e1000: 0001:02:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:15:17:0b:cb:12 e1000: 0001:02:00.0: e1000_probe: This device (id 8086:105e) will no longer be supported by this driver in the future. e1000: 0001:02:00.0: e1000_probe: please use the "e1000e" driver instead. e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection e1000: 0001:02:00.1: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:15:17:0b:cb:13 e1000: 0001:02:00.1: e1000_probe: This device (id 8086:105e) will no longer be supported by this driver in the future. e1000: 0001:02:00.1: e1000_probe: please use the "e1000e" driver instead. e1000: eth2: e1000_probe: Intel(R) PRO/1000 Network Connection Gianfar MII Bus: probed eth3: Gianfar Ethernet Controller Version 1.2, 00:d0:93:1a:92:6a eth3: Running with NAPI enabled eth3: 256/256 RX/TX BD ring size eth4: Gianfar Ethernet Controller Version 1.2, 00:d0:93:1a:92:6b eth4: Running with NAPI enabled eth4: 256/256 RX/TX BD ring size eth5: Gianfar Ethernet Controller Version 1.2, 00:d0:93:1a:92:6c eth5: Running with NAPI enabled eth5: 256/256 RX/TX BD ring size eth6: Gianfar Ethernet Controller Version 1.2, 00:d0:93:1a:92:6d eth6: Running with NAPI enabled eth6: 256/256 RX/TX BD ring size Uniform Multi-Platform E-IDE driver ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx f8000000.flash: Found 2 x16 devices at 0x0 in 32-bit bank Amd/Fujitsu Extended Query Table at 0x0040 f8000000.flash: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cmdlinepart partition parsing not available RedBoot partition parsing not available Creating 6 MTD partitions on "f8000000.flash": 0x00000000-0x00200000 : "kernel" 0x00200000-0x00500000 : "root" 0x00500000-0x07f00000 : "user" 0x07f00000-0x07f40000 : "env1" 0x07f40000-0x07f80000 : "env2" 0x07f80000-0x08000000 : "u-boot" NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 628 at 0x04e80000 Bad eraseblock 995 at 0x07c60000 Bad eraseblock 2051 at 0x10060000 Bad eraseblock 3608 at 0x1c300000 Bad eraseblock 3992 at 0x1f300000 cmdlinepart partition parsing not available Creating 1 MTD partitions on "e3010000.nand": 0x00000000-0x01000000 : "fs" TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. IP-Config: Complete: device=eth3, addr=192.168.210.7, mask=255.255.0.0, gw=255.255.255.255, host=tqm8548, domain=, nis-domain=(none), bootserver=192.168.3.1, rootserver=192.168.3.1, rootpath= Looking up port of RPC 100003/2 on 192.168.3.1 PHY: e0024520:02 - Link is Up - 100/Full Looking up port of RPC 100005/1 on 192.168.3.1 VFS: Mounted root (nfs filesystem). Freeing unused kernel memory: 144k init INIT: version 2.86 booting Welcome to DENX Embedded Linux Environment Press 'I' to enter interactive startup. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Setting clock : Thu Jan 1 01:00:06 CET 1970 [ OK ] Building the cache [ OK ] Setting hostname tqm8548: [ OK ] Mounting local filesystems: [ OK ] Enabling /etc/fstab swaps: [ OK ] INIT: Entering runlevel: 3 Entering non-interactive startup FATAL: Could not load /lib/modules/2.6.26-rc5-dirty/modules.dep: No such file or directory Bringing up loopback interface: [ OK ] FATAL: Could not load /lib/modules/2.6.26-rc5-dirty/modules.dep: No such file or directory Starting system logger: [ OK ] Starting kernel logger: [ OK ] Starting rpcbind: [ OK ] Mounting NFS filesystems: [ OK ] Mounting other filesystems: [ OK ] Starting xinetd: [ OK ] DENX ELDK version 4.2 build 2008-04-01 Linux 2.6.26-rc5-dirty on a ppc tqm8548 login: root Last login: Thu Jan 1 01:00:11 on console -bash-3.2#