0.000 ## Booting image at 00200000 ... 0.030 Image Name: Linux-2.4.25 0.080 Created: 2005-04-23 14:11:01 UTC 0.110 Image Type: PowerPC Linux Kernel Image (gzip compressed) 0.190 Data Size: 909254 Bytes = 887.9 kB 0.190 Load Address: 00000000 0.219 Entry Point: 00000000 1.191 Verifying Checksum ... OK 9.753 Uncompressing Kernel Image ... OK 12.928 Memory BAT mapping: BAT2=64Mb, BAT3=0Mb, residual: 0Mb 13.049 Linux version 2.4.25 (wd@denx.denx.de) (gcc version 3.3.3 (DENX ELDK 3.1 3.3.3-8)) #1 Sat Apr 23 16:10:46 MEST 2005 13.089 Motorola SPS Sandpoint Test Platform 13.169 Port by MontaVista Software, Inc. (source@mvista.com) 13.209 On node 0 totalpages: 16384 13.209 zone(0): 16384 pages. 13.259 zone(1): 0 pages. 13.259 zone(2): 0 pages. 13.419 Kernel command line: root=/dev/nfs rw nfsroot=192.168.3.1:/opt/eldk/ppc_82xx ip=192.168.3.15:192.168.3.1::255.255.0.0:sp8240:eth0:off panic=1 13.500 OpenPIC Version 1.2 (1 CPUs and 11 IRQ sources) at fdfd0000 13.529 time_init: decrementer frequency = 8.119684 MHz 13.769 Calibrating delay loop... 86.42 BogoMIPS 13.990 Memory: 62660k available (1480k kernel code, 484k data, 132k init, 0k highmem) 14.040 Dentry cache hash table entries: 8192 (order: 4, 65536 bytes) 14.090 Inode cache hash table entries: 4096 (order: 3, 32768 bytes) 14.180 Mount cache hash table entries: 512 (order: 0, 4096 bytes) 14.260 Buffer cache hash table entries: 4096 (order: 2, 16384 bytes) 14.321 Page-cache hash table entries: 16384 (order: 4, 65536 bytes) 14.401 POSIX conformance testing by UNIFIX 14.401 PCI: Probing PCI hardware 14.430 Linux NET4.0 for Linux 2.4 14.501 Based upon Swansea University Computer Society NET3.039 14.521 Initializing RT netlink socket 14.580 Thermal assist unit not available 14.580 Starting kswapd 15.642 initialize_kbd: Keyboard reset failed, no ACK 17.695 pty: 256 Unix98 ptys configured 17.735 keyboard: Timeout - AT keyboard not present?(ed) 17.786 keyboard: Timeout - AT keyboard not present?(f4) 17.886 Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled 17.946 ttyS00 at 0xfe0003f8 (irq = 4) is a 16550A 17.976 Generic RTC Driver v1.07 18.076 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize 18.116 loop: loaded (max 8 devices) 18.166 Linux Tulip driver version 0.9.15-pre12 (Aug 9, 2002) 18.226 tulip0: no phy info, aborting mtable build 18.306 eth0: Macronix 98715 PMAC rev 37 at 0xbffe00, 00:80:AD:8C:A3:78, IRQ 20. 18.377 pcnet32.c:v1.27a 10.02.2002 tsbogend@alpha.franken.de 18.456 eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html 18.597 eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin and others 18.667 eth1: PCI device 8086:1229, 00:02:B3:D1:FB:34, IRQ 19. 18.747 Board assembly 751767-004, Physical connectors present: RJ45 18.787 Primary interface chip i82555 PHY #1. 18.807 Secondary interface chip i82555. 18.887 General self-test: passed. 18.887 Serial sub-system self-test: passed. 18.967 Internal registers self-test: passed. 19.007 ROM checksum self-test: passed (0x8e695832). 19.087 Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 19.188 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx 19.217 W82C105: IDE controller at PCI slot 00:0b.1 19.258 W82C105: chipset revision 5 19.298 W82C105: 100% native mode on irq 16 19.398 ide0: BM-DMA at 0xbfffd0-0xbfffd7, BIOS settings: hda:DMA, hdb:DMA 19.468 ide1: BM-DMA at 0xbfffd8-0xbfffdf, BIOS settings: hdc:DMA, hdd:DMA 19.488 Probing IDE interface ide0... 19.537 ide0: Wait for ready failed before probe ! 20.108 Probing IDE interface ide1... 20.128 ide1: Wait for ready failed before probe ! 20.689 SCSI subsystem driver Revision: 1.00 20.750 kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 20.810 NET4: Linux TCP/IP 1.0 for NET4.0 20.840 IP Protocols: ICMP, UDP, TCP 20.890 IP: routing cache hash table of 512 buckets, 4Kbytes 20.949 TCP: Hash tables configured (established 4096 bind 8192) 22.492 IP-Config: Complete: 22.602 device=eth0, addr=192.168.3.15, mask=255.255.0.0, gw=255.255.255.255, 22.642 host=sp8240, domain=, nis-domain=(none), 22.723 bootserver=192.168.3.1, rootserver=192.168.3.1, rootpath= 22.752 NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. 22.823 Looking up port of RPC 100003/2 on 192.168.3.1 22.872 Looking up port of RPC 100005/1 on 192.168.3.1 22.973 VFS: Mounted root (nfs filesystem). 22.992 Freeing unused kernel memory: 132k init 23.453 INIT: version 2.84 booting 24.576 Welcome to DENX Embedded Linux Environment 24.625 Press 'I' to enter interactive startup. 29.432 Building the cache [ OK ] 29.702 Mounting proc filesystem: [ OK ] 30.002 Configuring kernel parameters: [ OK ] 31.094 Setting clock : Sat Apr 23 18:54:45 MEST 2005 [ OK ] 31.274 Setting hostname sp8240: [ OK ] 31.725 modprobe: Can't open dependencies file /lib/modules/2.4.25/modules.dep (No such file or directory) 32.356 Activating swap partitions: [ OK ] 33.217 Finding module dependencies: depmod: Can't open /lib/modules/2.4.25/modules.dep for writing 33.277 [FAILED] 33.467 Checking filesystems 33.668 [ OK ] 33.818 Mounting local filesystems: [ OK ] 35.100 Enabling swap space: [ OK ] 35.370 modprobe: Can't open dependencies file /lib/modules/2.4.25/modules.dep (No such file or directory) 39.366 INIT: Entering runlevel: 3 39.857 Entering non-interactive startup 41.319 Setting network parameters: [ OK ] 44.644 Bringing up loopback interface: [ OK ] 45.815 Starting system logger: [ OK ] 45.995 Starting kernel logger: [ OK ] 46.887 Initializing random number generator: [ OK ] 49.420 Starting portmapper: [ OK ] 49.691 Mounting NFS filesystems: [ OK ] 49.891 Mounting other filesystems: [ OK ] 54.398 Starting xinetd: [ OK ] 54.878 56.160 sp8240 login: