Skip to main content.

=>
=> setenv bootfile /tftpboot/tqm8548/uImage-duts
=> setenv rootpath /opt/eldk-4.2/ppc_85xx/
=> run net_nfs
Speed: 100, full duplex
Using TSEC0 device
TFTP from server 192.168.3.1; our IP address is 192.168.210.7
Filename '/tftpboot/tqm8548/uImage-duts'.
Load address: 0x1000000
Loading: #################################################################
    ##################################
done
Bytes transferred = 1439847 (15f867 hex)
Speed: 100, full duplex
Using TSEC0 device
TFTP from server 192.168.3.1; our IP address is 192.168.210.7
Filename '/tftpboot/tqm8548/tqm8548.dtb'.
Load address: 0x400000
Loading: #
done
Bytes transferred = 10465 (28e1 hex)
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:    Linux-2.6.26-rc5-dirty
   Created:    2008-06-08  12:06:49 UTC
   Image Type:    PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1439783 Bytes =  1.4 MB
   Load Address: 00000000
   Entry Point:    00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
## Flattened Device Tree blob at 00400000
   Booting using the fdt blob at 0x400000
Using TQM85xx machine description
Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
Linux version 2.6.26-rc5-dirty (wolf@pollux.denx.de) (gcc version 4.2.2) #1 Sun Jun 8 14:06:27 MEST 2008
console [udbg0] enabled
setup_arch: bootmem
tqm85xx_setup_arch()
Found FSL PCI host bridge at 0x00000000e0008000. Firmware bus number: 0->0
PCI host bridge /pci@e0008000 (primary) ranges:
 MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000
  IO 0x00000000e2000000..0x00000000e2ffffff -> 0x0000000000000000
Found FSL PCI host bridge at 0x00000000e000a000. Firmware bus number: 0->1
PCI host bridge /pcie@e000a000   ranges:
 MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
  IO 0x00000000ef000000..0x00000000f6ffffff -> 0x0000000000000000
arch: exit
Zone PFN ranges:
  DMA        0 ->    131072
  Normal     131072 ->    131072
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:         0 ->   131072
Built 1 zonelists in Zone order, mobility grouping on.   Total pages: 130048
Kernel command line: root=/dev/nfs rw nfsroot=192.168.3.1:/opt/eldk-4.2/ppc_85xx/ ip=192.168.210.7:192.168.3.1::255.255.0.0:tqm8548:eth3:off panic=1 console=ttyS0,115200
mpic: Setting up MPIC " OpenPIC    " version 1.2 at e0040000, max 1 CPUs
mpic: ISU size: 80, shift: 7, mask: 7f
mpic: Initializing for 80 sources
PID hash table entries: 2048 (order: 11, 8192 bytes)
clocksource: timebase mult[3c00001] shift[22] registered
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 516352k/524288k available (2812k kernel code, 7620k reserved, 108k data, 104k bss, 144k init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 192 bytes
NET: Registered protocol family 16

PCI: Probing PCI hardware
PCI: 0001:01:00.0: class b20 doesn't match header type 01. Ignoring class.
PCI: Cannot allocate resource region 2 of device 0000:00:1c.0, will remap
PCI: Cannot allocate resource region 2 of device 0001:02:00.0, will remap
PCI: Cannot allocate resource region 2 of device 0001:02:00.1, will remap
PCI: Bridge: 0001:01:00.0
  IO window: 0000-0fff
  MEM window: 0xc0000000-0xc00fffff
  PREFETCH window: 0x00000000c0100000-0x00000000c01fffff
pci 0001:01:00.0: enabling device (0106 -> 0107)
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
msgmni has been set to 1009 for ipc namespace c02ce3dc
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
aer: probe of 0001:01:00.0:pcie01 failed with error -38
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.2 $ 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 42) is a 16550A
console handover: boot [udbg0] -> real [ttyS0]
serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 42) is a 16550A
brd: module loaded
loop: module loaded
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e1000: 0000:00:1c.0: e1000_probe: (PCI:66MHz:32-bit) 00:0e:0c:d7:f5:f4
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
e1000: 0001:02:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:15:17:0b:cb:12
e1000: 0001:02:00.0: e1000_probe: This device (id 8086:105e) will no longer be supported by this driver in the future.
e1000: 0001:02:00.0: e1000_probe: please use the "e1000e" driver instead.
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
e1000: 0001:02:00.1: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:15:17:0b:cb:13
e1000: 0001:02:00.1: e1000_probe: This device (id 8086:105e) will no longer be supported by this driver in the future.
e1000: 0001:02:00.1: e1000_probe: please use the "e1000e" driver instead.
e1000: eth2: e1000_probe: Intel(R) PRO/1000 Network Connection
Gianfar MII Bus: probed
eth3: Gianfar Ethernet Controller Version 1.2, 00:d0:93:1a:92:6a
eth3: Running with NAPI enabled
eth3: 256/256 RX/TX BD ring size
eth4: Gianfar Ethernet Controller Version 1.2, 00:d0:93:1a:92:6b
eth4: Running with NAPI enabled
eth4: 256/256 RX/TX BD ring size
eth5: Gianfar Ethernet Controller Version 1.2, 00:d0:93:1a:92:6c
eth5: Running with NAPI enabled
eth5: 256/256 RX/TX BD ring size
eth6: Gianfar Ethernet Controller Version 1.2, 00:d0:93:1a:92:6d
eth6: Running with NAPI enabled
eth6: 256/256 RX/TX BD ring size
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
f8000000.flash: Found 2 x16 devices at 0x0 in 32-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
f8000000.flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Creating 6 MTD partitions on "f8000000.flash":
0x00000000-0x00200000 : "kernel"
0x00200000-0x00500000 : "root"
0x00500000-0x07f00000 : "user"
0x07f00000-0x07f40000 : "env1"
0x07f40000-0x07f80000 : "env2"
0x07f80000-0x08000000 : "u-boot"
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 628 at 0x04e80000
Bad eraseblock 995 at 0x07c60000
Bad eraseblock 2051 at 0x10060000
Bad eraseblock 3608 at 0x1c300000
Bad eraseblock 3992 at 0x1f300000
cmdlinepart partition parsing not available
Creating 1 MTD partitions on "e3010000.nand":
0x00000000-0x01000000 : "fs"
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
IP-Config: Complete:
     device=eth3, addr=192.168.210.7, mask=255.255.0.0, gw=255.255.255.255,
     host=tqm8548, domain=, nis-domain=(none),
     bootserver=192.168.3.1, rootserver=192.168.3.1, rootpath=
Looking up port of RPC 100003/2 on 192.168.3.1
PHY: e0024520:02 - Link is Up - 100/Full
Looking up port of RPC 100005/1 on 192.168.3.1
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 144k init
INIT: version 2.86 booting
      Welcome to DENX Embedded Linux Environment
      Press 'I' to enter interactive startup.
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Setting clock : Thu Jan    1 01:00:06 CET 1970 [   OK  ]
Building the cache [  OK  ]
Setting hostname tqm8548:  [  OK  ]
Mounting local filesystems:  [   OK  ]
Enabling /etc/fstab swaps:  [  OK  ]
INIT: Entering runlevel: 3
Entering non-interactive startup
FATAL: Could not load /lib/modules/2.6.26-rc5-dirty/modules.dep: No such file or directory
Bringing up loopback interface:    [  OK   ]
FATAL: Could not load /lib/modules/2.6.26-rc5-dirty/modules.dep: No such file or directory
Starting system logger: [  OK  ]
Starting kernel logger: [  OK  ]
Starting rpcbind: [  OK    ]
Mounting NFS filesystems:  [  OK  ]
Mounting other filesystems:  [   OK  ]
Starting xinetd: [  OK   ]

DENX ELDK version 4.2 build 2008-04-01
Linux 2.6.26-rc5-dirty on a ppc

tqm8548 login: root
Last login: Thu Jan  1 01:00:10 on console
-bash-3.2#